Security Link SL150 Guida alla Risoluzione dei Problemi Scaricare il pdf (Pagina 123)

25–1

SECTION 25

Troubleshooting Guide

••••••••••••••••••••••••••••••••••••••••••••••••••

(including Wireless)

SYMPTOM POSSIBLE CAUSE REMEDY

1. Transmitter signal not

received at

5881/5882.

1a. Transmitter or 5881/5882 not properly

powered.

1a Check or change transmitter's battery.

Check

SL150

's AC power.

1b. If transmitter

5827/5827BD

, House

Code not set in field

✱

24, or transmitter

not set to same House Code set in that

field.

1b. Check code switches inside transmitter.

Must match with RF House Code

programmed in

SL150

1c. Transmitter located too far from RF

receiver.

1c. Move transmitter or RF receiver.

1d. Metal shielding between transmitter and

RF receiver.

1d. Check for large metal obstructions,

then relocate transmitter if necessary.

1e. Transmitter malfunctioning. 1e. Verify by activating 5881/5882 with

another, similar transmitter. If O.K.

now, return defective transmitter.

1f. 5881/5882 malfunctioning. 1f. Verify by making sure other

transmitters cannot activate 5881/5882.

If defective, replace and return original

5881/5882.

1g. Transmitter No. (zone) not programmed. 1g. Verify programming.

1h. 5881/5882 address incorrect. 1h. Set DIP switch on 5881/5882 for

address “0.”

1i. Field

✱

22 not set properly. 1i. Set field

✱

22 for “1 or “4”.”

2. Transmitter zone number

appears during Transmitter

Sniffer mode, but does not

clear.

2a. Transmitter zone type (ZT) is set to

(Not Used).

2b. Transmitter battery not installed.

2a. Set ZT to a valid active zone type in

field

✱

56.

2b. Install proper battery.

2c. 5800 system transmitter not

enrolled

system.

2c. Enroll unit in field

✱

56.

3. LOW BATTERY message on

keypad.

3a.

Bat

System Lo Ba

t (no zone nos.):

System battery is low or missing.

3b.

Bat

Lo Bat

: Remote RF keypad

battery is low.

3a. Verify that battery charging circuit is

working. If ok, replace battery.

3b. Replace remote RF keypad battery

3c.

Bat

Lo Bat

: Transmitter for zone

“nn” has a low battery.

3c. Replace transmitter battery in zone

"nn."

4. Periodic beep(s) from

keypad

4a. System is in Test mode.

4b. A transmitter low battery has occurred

and is displayed.

4c. A supervision Check has occurred.

4a. Enter [Code] + OFF to exit Test mode.

4b. Enter [Code] + OFF and replace the

battery.

4c. Check the transmitter indicated.

Restore communication to the receiver

to cancel the condition.

5. With 5800 system, no

response to a transmitter in

normal operation, although

zone number clears during

Transmitter Sniffer mode.

5a. Put control in Test mode. If zone does not

respond, try operating the tamper switch

or another input to the transmitter.

If another input causes the zone to be

displayed, the wrong input was

enrolled

when programming.

5a. Delete input's serial number (not the

zone), and enroll the proper input (see

field

✱

56).

1 2 ... 118 119 120 121 122 123 124 125 126 127 128 ... 143 144

Commenti su questo manuale

Nessun commento

Security Link SL150 Guida alla Risoluzione dei Problemi Pagina 123

Commenti su questo manuale

Prodotti e manuali riguardandi Sistemi di controllo di accesso Security Link SL150